Mineral Oil Transformer Manufacturer & Factories in Italy

A 2025 procurement and application guide for Italian utilities, EPC contractors, industrial plants and renewable developers comparing CE-certified mineral oil distribution transformers, pad-mounted units and factory-audited export supply from Jiangsu Wisegj Power Co., Ltd.

Italy 50 Hz FocusIEC 60076 / CE10–35 kV ClassFactory Audit Support
Product Recommendations for Italy

Eight Mineral Oil Transformer Configurations for Italian Projects

Italy is not a generic export market. The country runs at 50 Hz, commonly distributes at 10 kV, 15 kV or 20 kV, and uses 400/230 V low-voltage systems in many commercial and industrial installations. A transformer designed for a 60 Hz, 480 V project should not be offered as a default Italian solution. The eight mineral oil transformer families below are recommended starting points, from compact 50 kVA distribution units to 2,500 kVA pad-mounted and industrial oil-immersed designs. Confirm frequency, voltage class, vector group, impedance, losses, cooling, oil type, enclosure and CE documentation before tender award.

C CE S11 10kV 20kV 35kV 50kVA to 250kVA three phase oil immersed distribution transformer

C CE S11 10/20/35 kV 50–250 kVA Three-Phase Oil-Immersed Distribution Transformer

Recommended for commercial buildings, small industrial feeders and secondary distribution where a compact 50 Hz oil-immersed unit is required. Typical Italian enquiries specify 10/0.4 kV or 20/0.4 kV, Dyn11, ±2×2.5% taps and routine tests to IEC 60076.

50–250 kVA10–35 kVDyn11 options
View product
C CE 50/60Hz 10kV 20kV 35kV 300kVA to 750kVA three phase pad mounted transformer

C CE 50/60 Hz 10/20/35 kV 300–750 kVA Three-Phase Pad-Mounted Transformer

For underground MV networks, renewable interconnections and urban developments that need a pad-mounted footprint. Loop or radial feed, dead-front bushings, mineral oil and project-specific no-load/load losses support EU efficiency evaluation.

300–750 kVAPad-mountedLoop / radial
View product
CE industrial three phase pad mounted pedestal transformer 6kV 10kV 15kV 20kV 35kV

CE Industrial 6–35 kV 100–630 kVA Three-Phase Pad-Mounted Pedestal Transformer

For industrial plants, logistics parks and commercial campuses where the transformer sits close to the load. The pedestal design helps address access, tamper resistance and space constraints in retrofit or phased-build projects.

100–630 kVAIndustrial6–35 kV
View product
CE certification 750kVA 10kV 20kV 35kV loop feed pad mounted distribution transformer

CE 750 kVA 10/35 kV Three-Phase Loop-Feed Pad-Mounted Distribution Transformer

For Italian EPCs needing loop-feed flexibility, sectionalizing and future load growth. Suited to community microgrids, public infrastructure and underground distribution where cable routing and footprint influence layout.

750 kVALoop feed10/35 kV
View product
C CE S11 50/60Hz 6kV 10kV 15kV 20kV 35kV oil immersed distribution transformer

C CE S11 50/60 Hz 6–35 kV 50–300 kVA Three-Phase Oil-Immersed Transformer

A versatile distribution transformer for utility, rural electrification and industrial retrofit work. Options include low-loss cores, sealed tank designs, 33 kV class duty where specified, and English or Italian nameplate text for the project file.

50–300 kVA6–35 kVLow-loss
View product
C certified 75kVA to 2500kVA oil type three phase pad mounted transformer

C Certified 75–2,500 kVA Oil-Type Three-Phase Pad-Mounted Transformer, 35 kV Input / 480 V Output

Useful for exported equipment packages and industrial projects that require a pad-mounted oil transformer with 35 kV input and 480 V output. Because 480 V is not the standard Italian LV utilization voltage, confirm the single-line diagram, frequency and downstream equipment before ordering.

75–2500 kVA35 kV input480 V output
View product
ANSI single phase pole mounted transformer 15kVA to 100kVA for industrial power supply

ANSI 6–35 kV 15–100 kVA Single-Phase Pole-Mounted Transformer for Industrial Power Supply

For rural feeders, auxiliary supplies and distributed loads where single-phase pole mounting is preferred. This is not the default Italian MV choice, but it can be relevant for islands, off-grid packages and international project standards embedded in an Italian EPC scope.

15–100 kVAANSIPole mounted
View product
C CE 10kV 20kV 35kV 50kVA to 500kVA oil immersed transformer for industrial power supply

C CE 10/20/35 kV 50–500 kVA Oil-Immersed Transformer for Industrial Power Supply

A broad industrial workhorse for manufacturing plants, water treatment, ports and cold-chain facilities. Custom impedance, tap range, bushings, protection and paint systems can be aligned with the project's fault level and environmental conditions.

50–500 kVAIndustrial10–35 kV
View product

For Italian tenders, always compare the proposed nameplate against the project single-line diagram. Where a 480 V or 60 Hz design appears in an RFQ, verify whether the equipment is for an Italian installation or an overseas package embedded in the Italian EPC scope.

Factory Verification & E-E-A-T

What “Factories in Italy” Means for a Credible Manufacturer Search

The search phrase “Mineral Oil Transformer Manufacturer & Factories in Italy” mixes two buying intentions. One buyer may want a factory physically located in Italy; another may want a proven mineral oil transformer manufacturer that can deliver to Italy with CE documentation, factory audit evidence and local project support. We separate those intentions clearly. Jiangsu Wisegj Power Co., Ltd. is a China-based manufacturer with a verified production base in Suzhou, Jiangsu. We do not claim to operate an Italian factory. If your tender requires an Italian manufacturing address, we will tell you before quotation. If your requirement is a factory-audited IEC/CE supplier with export experience, Italian voltage know-how and full test documentation, Wisegj can be shortlisted.

That transparency matters for E-E-A-T because transformer procurement is not a catalogue purchase. The legal manufacturer named on the nameplate, the holder of the CE certificate, the factory that performed routine tests and the company issuing the declaration of conformity should be consistent. Italian buyers should verify the factory address, certificate scope, test equipment, oil test records, traceability of core and copper, and the availability of third-party witness inspection. Wisegj provides these documents and welcomes audit checks before order.

  • Production base and certificate holder verified through independent audit evidence.
  • CE oil-immersed certificate No. M.2025.206.C121882; CE power transformer No. 3N230310.JYTU038.
  • ISO 9001 No. 62824Q6052R0S, ISO 14001 No. 62824E6053R0S and ISO 45001 No. 62824S6054R0S.
  • Routine test reports for winding resistance, ratio, impedance, losses, applied and induced voltage.
  • Oil dielectric strength, SDS and mineral oil traceability for liquid-filled units.
  • Third-party witness inspection and pre-shipment documentation review available.
Contact Us
Jiangsu Wisegj Power factory and engineering team supporting mineral oil transformer projects
TÜV Rheinland logo

Production capability, floorspace and quality inspection verified onsite by TÜV Rheinland, an independent third-party inspection body.

20+Years of team experience in transformer engineering and export projects.
500 kVMaximum voltage class supplied across the wider Wisegj power equipment portfolio.
6,847 m²Verified production floorspace for manufacturing, assembly and testing.
50+R&D and technical engineers supporting drawings, testing and customization.
211Qualified supply-chain partners for silicon steel, copper, bushings and accessories.
4.9/5Average buyer rating supported by export documentation and after-sales response.
Local Application Scenarios

Where Mineral Oil Transformers Fit in Italy’s Local Energy Landscape

Italy’s geography, grid structure and regulatory environment create specific transformer applications. The following six scenarios are the most common reasons Italian buyers request mineral oil transformers from an IEC/CE-oriented manufacturer.

Utility and Secondary Distribution

10/15/20 kV to 400/230 V distribution remains the backbone of Italian local supply. Oil-immersed distribution transformers are specified for compact footprint, proven thermal behavior and maintainable cost. Provide the DSO or EPC specification for vector group, impedance, loss limits, protection and enclosure.

Solar, Wind and Storage Projects

Puglia, Sicily, Sardinia and other high-renewable areas require step-up and interconnection transformers. Pad-mounted and oil-immersed designs are often used where footprint and cable routing matter. The transformer is only one part of grid compliance, so confirm protection interface, voltage regulation and local grid-code requirements with the project engineer.

Industrial Clusters and Manufacturing

Lombardy, Veneto, Emilia-Romagna and other industrial regions often need transformers for motor-heavy loads, harmonics, duty cycles and expansion phases. Custom impedance, cooling and protection coordination can reduce nuisance tripping and improve total cost of ownership.

Data Centres and EV Charging

Milan, Rome and other commercial centres face space constraints and rising loss evaluation. Low-loss mineral oil transformers, compact pad-mounted layouts and documented test reports help developers compare capital cost against operating loss over the project life.

Ports, Rail and Coastal Infrastructure

Genoa, Trieste, Ravenna and other coastal locations require attention to humidity, salt mist, corrosion protection and oil containment. For rail and port projects, confirm seismic requirements, enclosure paint systems and maintenance access before finalizing the design.

Public Infrastructure and Historic Centres

Hospitals, schools, tunnels and urban regeneration projects often require noise control, fire safety and discreet installation. Mineral oil units can be supplied with containment and protection accessories; natural ester may be considered where the fire or environmental strategy calls for it.

Technical Buying Guide

A Practical Specification Matrix for Italian Mineral Oil Transformer Enquiries

Use this matrix to prepare a clearer RFQ. It reduces clarification rounds and helps compare an Italian supplier, a European distributor and a factory-audited import manufacturer on the same technical basis.

Specification AreaTypical Italy FocusWisegj Design ResponseEvidence Supplied
Frequency and Voltage50 Hz; 10/15/20/35 kV MV; 400/230 V LV for many projects.Design to the project single-line diagram, with custom taps, vector group and BIL where required.Nameplate drawing, ratio test and vector group test.
Efficiency and LossesEU Ecodesign evaluation and total cost of ownership comparison.Low-loss CRGO or amorphous core options; calculated no-load and load losses.Loss measurement report and guaranteed loss values.
Oil SystemMineral oil to IEC 60296; containment, fire strategy and maintenance access.Sealed or corrugated tank designs, oil-level and temperature accessories, mineral oil or ester discussion.Oil test record, SDS and tank drawing.
Enclosure and EnvironmentUrban, coastal, seismic and humidity considerations.Pad-mounted or pedestal enclosure, corrosion protection and paint specification.GA drawing, enclosure data and paint specification.
Protection and AccessoriesFuses, switches, gauges, pressure relief and cable termination requirements.Project-specific accessory list coordinated with the EPC protection scheme.Wiring diagram, factory check sheet and O&M manual.
Standards and DocumentsIEC 60076, CE marking, ISO management systems and customs documentation.CE certificate scope, declaration of conformity and English documentation package.Certificate numbers, routine test reports and packing documents.

Note: Italy commonly uses 50 Hz. Where a tender includes 60 Hz or 480 V equipment, confirm whether the transformer is for an Italian site or an overseas package within the EPC scope. Mineral oil is a proven insulating fluid, but fire strategy, oil containment and local installation rules must be reviewed by the responsible engineer.

Company Advantages

Manufacturing Advantages That Matter in an Italian Tender

Italian buyers often compare a European supplier’s local service against an import supplier’s engineering flexibility and cost. Wisegj’s advantage is not a claim of an Italian factory; it is auditable manufacturing, customization and documentation discipline. Our team has supplied Fortune 500 companies and maintains a 4.9/5 average buyer rating, with 24-hour pre-sale and after-sale technical response.

Verified Factory Capacity

6,847 m² inspected floorspace with dedicated winding, core assembly, drying, tanking and test areas.

In-House Routine Testing

Ratio, resistance, loss, impedance, dielectric and oil BDV tests documented for each serial number.

IEC, CE and ANSI Customization

Ratings, vector group, impedance, taps, bushings, cooling, enclosure and protection adapted to project specifications.

Complete Documentation

GA drawings, nameplate drafts, routine test reports, O&M manuals and customs documents supplied in English.

211 Supply Partners

Qualified sources for silicon steel, copper, bushings and accessories support stable lead times.

24-Hour Engineer Response

Technical questions and after-sales issues receive a qualified reply within one working day.

Export Logistics to Italy

Seaworthy packing, shock indicators and Incoterms coverage from EXW to DDP, with routing to Italian ports.

OEM, ODM and Nameplate Localization

Design-based customization, English or Italian nameplate text and project-specific document packages.

Factory, Testing and Export Evidence

Visual Documentation for Italian Buyer Due Diligence

These images are drawn from the original Wisegj company and production content. They help Italian buyers prepare a factory audit checklist, a pre-inspection plan or a supplier comparison file.

Italy Buyer FAQ

FAQ: What Italian Buyers Commonly Ask Before Ordering a Mineral Oil Transformer

Straight answers for procurement teams comparing a manufacturer, a distributor and a factory-audited import supplier.

Do you have a mineral oil transformer factory in Italy?

No. Wisegj’s production base is in Suzhou, Jiangsu, China. We do not present ourselves as an Italian factory. If your tender requires a manufacturing address in Italy, we will state that clearly before quotation. For buyers comparing factory-audited export suppliers, we provide production floorspace evidence, certificate scope, routine test reports and audit support.

Can you supply CE-certified mineral oil transformers to Italy?

Yes. Oil-immersed transformer product lines hold CE certification, including CE oil-immersed certificate No. M.2025.206.C121882 and CE power transformer certificate No. 3N230310.JYTU038. The documentation package can include the declaration of conformity, routine test reports, nameplate drawing and O&M manual. Final applicability must be checked against the project specification.

What voltage ratings are common for Italian projects?

Italy operates at 50 Hz. Common MV distribution classes include 10 kV, 15 kV and 20 kV, with 35 kV class equipment also used in some industrial and interconnection projects. LV utilization is often 400/230 V. Do not assume a US-style 480 V secondary is suitable for an Italian site unless the single-line diagram explicitly requires it.

Are you a manufacturer or a trading company?

Jiangsu Wisegj Power Co., Ltd. is a manufacturer and exporter with an audited production base. Production capability, floorspace and quality inspection have been verified onsite by TÜV Rheinland. Italian buyers can request a factory video tour, certificate copies, test equipment list and third-party witness inspection before shipment.

How do you handle EU efficiency and loss evaluation?

We design to the project’s loss limits and can provide calculated no-load and load losses for comparison. Low-loss CRGO or amorphous core options are available, and routine tests include loss measurement. Italian buyers should include the applicable EU Ecodesign tier, evaluation method and any total-cost formula in the RFQ so offers can be compared on the same basis.

What documents are needed for Italian customs and installation?

A typical package includes the CE declaration of conformity, routine test reports, GA drawing, nameplate drawing, packing list, commercial invoice, bill of lading, certificate of origin, O&M manual and oil safety data sheet where applicable. For site installation, also confirm cable termination details, protection settings and local electrical safety requirements with the responsible engineer.

What are typical lead times and shipping terms to Italy?

Lead time depends on rating, customization, drawing approval and test schedule. Shipments to Italy can be routed through ports such as Genoa, La Spezia, Ravenna or Trieste depending on the final destination and freight plan. We can quote EXW, FOB, CIF, CIP, DDP and other Incoterms, with T/T, L/C and other payment methods agreed per contract.

Can you customize a mineral oil transformer for an Italian EPC specification?

Yes. Customization covers ratings, frequency confirmation, voltage class, vector group, impedance, tap range, bushing configuration, cooling method, mineral oil or ester discussion, enclosure color, protection accessories and nameplate language. OEM, ODM, design-based and sample-based customization are available, and third-party witness testing is welcome.

Inquiry Conversion

Send Your Italian Project Specification for a Compliant Quotation

Share your single-line diagram, transformer datasheet or tender specification. A transformer engineer will review voltage, frequency, losses, oil system, enclosure, protection and documentation requirements, then return an Italy-specific quotation with drawings, certificate scope and routine test plan. For faster evaluation, include the destination city or port, required delivery date and any factory audit or witness inspection requirement.

Contact Us

Email: [email protected] · Jiangsu Wisegj Power Co., Ltd. · Suzhou, Jiangsu, China · IEC / CE / ISO documentation available for review.